Lock Heat Pump Heat Pump Inactive Press & Hold Power for 5 seconds Follow these steps to set the pool temperature. How To: Set Pool Temperature 10 Step 1 Step Verify the heater's power LED is illuminated, and put the heater is the desired mode. Using the up and down arrows adjust the heater to the desired temperature. 2
Learn More5.4 Except there is water level error, hot water tank temp sensor error, when there is other temp error, high and low pressure error protection, electric heater
Learn MoreThe Pool Heat pump is brand spanking new! Its a 3 phase 50kw unit. Now on cooling the High pressure drops to 0psi and the unit trips out and
Learn MoreHighly conductive copper motor-Efficient & low heat generation. 1x Water Pump. Colour: Yellow. Efficient cooling system- the pump can run cool and quiet even under high loads and continuous operation. 1800W Water Pump High Pressure Multi Stage Farm Pool Rain Tank Irrigation Garden. Item information. Condition: Brand New Brand New. Bulk
Learn MoreHP and HP 6 - Low water flow or faulty high pressure control in the unit. Check water flow / backwash. Unit 6 HP will show after the defect (HP 6). This will cause the unit to shut down for safety. FLO & FL3 - Possible reasons: • The filter is in the backwash state. • The filter pump is turned off. • The filter is dirty.
Learn MoreThe swimming pool heat pump is one of the most economical systems to pumps which include water flow protection, high and low pressure
Learn MoreHP and HP 6 – Low water flow or faulty high pressure control in the unit. Check water flow / backwash. Unit 6 HP will show after the defect (HP 6). This will
Learn MorePoor water flow can sometimes trigger a High Pressure message, this means that the heat pump is creating heat but there is not enough water going though the machine to carry the heat out into the pool. Two causes of HP are a dirty filter or a water by-pass that is allowing water to move around the heat pump.
Learn More4. The high pressure protection switch is damaged. Troubleshooting: replace the high pressure protection switch. 5. The default water outlet temperature of the air source heat pump water heater unit is 55℃. If the temperature is set too high, the high-pressure protection failure will also occur.
Learn More17/07/ · In ground pool Aqua Comfort Heat Pump throwing an HP code (high pressure switch open). I have cleaned the cell with mixture of acid and water and the flow of water to the heater is fine. Says the other possibility is a defective high-pressure switch. Is it easy to find one of those and easy to replace?
Learn MoreERROR LCD CODE Low pressure Malfunction of Gas change too low. Possible system system 1 A11 blockage High pressure Malfunction of Gas change too high.
Learn MoreHP & HP6 - Low water flow in the unit or faulty high pressure control. Check water flow/backwash. The unit will show (HP6) after 6 HP faults. This will stop the unit for protection. FLo & FL3 - Possible causes: • The filter is in backwash position. • The filter pump is stopped. • The filter is dirty. • Shortage of water to pool pump.
Learn MoreStarting at £48.00. View Options. Pool Bypass Kits - Swimming Pool Heat Pumps 5. Savings up to 60%. Starting at £64.50. View Options. Show per page. These heat source pumps for swimming pools use innovative technology that challenges how pools are currently heated. With their top-of-the-line technology, these swimming pool heat pumps are
Learn MoreThank you for deciding on an open-air swimming pool heat pump from SET The yellow icons LP or HP then indicate a low pressure or high pressure fault.
Learn MoreTo use this guide, determine the model number of the heat pump and the nature of the problem. Refer to page one to find the appropriate page for the problem and follow the flow charts to the solution. If you have further questions Call Hayward's tech service department at 908-355-7995 High voltage. Danger! Use extreme caution.
Learn MorePoor water flow can sometimes trigger a High Pressure message, this means that the heat pump is creating heat but there is not enough water
Learn MoreReplace display board and wire harness Replace pressure switch. YES NO, Unit operates. Figure A dEFRefer To Page 10, Rotate dial counter clockwise to check for mis-adjustment. Switch will ‘close’ and reading will be zero Ohms. cSHRefer To Page 10, cOPRefer To Page 10, 2, What’s On The Display? On R-22 units abandon existing switch.
Learn MoreCheck your power source. Heat pump owners often forget to perform this simple check and jump right to more tedious ones. Make sure your breaker has not tripped and that the disconnect switch of your heat pump (located adjacent to your unit, typically on a wall or a post) is turned on. Ensure that your heat pump is getting sufficient water flow.
Learn MoreHigh Ref Pressure is normally caused when the refrigerant is not cooled off by the pool water circulating thru the heat exchanger. If your
Learn MoreIn salt water chlorinated pools, the total TDS can be as high as 6000ppm. Page 4. 4. Water Chemistry. 3. Warnings. 5.
Learn MoreIf not, it could cause an injury due to the high speed running fan or an electrical shock. Do not continue to run the unit when there is something wrong or
Learn MoreInternal safety devices may deactivate the heat pump with the following errors: ○. HIGH PRESSURE FAULT. ○. HP5 SYSTEM LOCKOUT. ○. LOW PRESSURE FAULT.
Learn MoreThe water flow inside the heat pump is insufficient There is no water circulation inside the heat pump The flow switch is defective: Make sure the circulating pump works; Make sure the bypass valves are properly positioned; Check the skimmer (no obstruction); Check the water pressure gauge of the heat pump, it should read between 10 and 15 psi
Learn MoreMedallion Energy 3055 Tech Park Way Deland, FL 32724 407-786-0000. Hours Mon-Fri: 8am - 7pm Saturday: 9am - 5pm Sunday: By Appointment
Learn MoreAfter that, move on to test the heater's temperature reading to the actual water temperature. You will need a thermometer. Replace the inlet water temperature sensor if the difference is large.
Learn MoreMedallion Energy 3055 Tech Park Way Deland, FL 32724 407-786-0000. Hours Mon-Fri: 8am - 7pm Saturday: 9am - 5pm Sunday: By Appointment
Learn MoreCopyright © 2021 PEAKEDNESS Inc. All rights reserved.