USG Middle East يو إس جي للشرق الأوسط

USG Shaftwall CH Stud, used to construct elevator shafts, mechanical shafts, stair shafts, services risers, air return shafts and horizontal shaft wall 

Studs @ 24" O.C. J-Tabbed Track Detail 1 Pan-Head Screws on both sides of all metal intersections ClarkDietrich Shaftwall Construction Details J-Tabbed Track J-Tabbed Track Detail 2 Detail 3 Door Opening Room Side J-Tabbed Track 20-gauge or heavier Gypsum

USG Middle East Shaftwall Access Panel - Heavy Duty is ideal for for shaftwall, plum walls and brick wall installation, comes with mounting claws for simple wall installation. Add To Favorites Add to Compare Heavy Duty Shaft Wall Wet Area Size Product Identifier Qty Order Sample Add To My Project List Performance Specifications Product Items

USG shaft wall systems are non-loadbearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are finished later, along with interior partitions. Installation is quick and easy, using components and application procedures familiar to drywall contractors.

1" (25.4 mm) DensGlass Shaftliner panels may be abutted, spliced or stacked within the cavity. The shorter panel should be a minimum 2' (610 mm) tall to engage two stud tabs on each panel edge. Joints of adjacent panels should be alternately stacked or staggered to prevent a continuous horizontal joint.

USG Shaft Wall Systems are non-load bearing gypsum wall partition assemblies constructed from outside the shaft at each floor.

Horizontal Shaftwall Designed for ceiling or duct shaft and composed of 1" (25.4 mm) ToughRock® Shaftliner or DensGlass® Shaftliner panel supported by 2-1/2" (64 mm), 4" (102 mm) or 6" (152 mm) C-T studs and three layers of 1/2" (12.7 mm) ToughRock® Fireguard C® or 1/2" (12.7 mm) DensArmor Plus® Fireguard C® gypsum board. Hourly Rating: 2-hour

Use CGC Shaft Wall Systems to construct elevator shafts, mechanical shafts, stairwells, air return shafts and horizontal membranes. These shafts are vital for vertical communication, power, water, fresh air, exhaust and a means of egress. Solid Shafts Horizontal Stud Shafts

SHEETROCK brand shaft wall systems have been comprehensively tested for 1- to 4-hour fire resistance ratings (UL Design No U415) only when all of the system 

disclaimer: the usg product details contained herein are intended for use as product reference material by architects, engineers, other design professionals, fire resistant assemblies head of wall details usg j2132 rev 0 issued 10/19/2015. scale: 3" = 1' - 0" 2 hr head of wall ul hw-d-0627 1 scale: 3" = 1' - 0" 2 hr head of wall ul hw-s-0001 4

USG Shaftwall/Area Separation Walls · Aluminum Break Away Clips for H-Stud Systems · Deep Leg J-Track · J-Runner 34 mil · JL Corner · Jamb Strut · H-Stud 34 mil · H- 

USG Shaft Wall Systems - CEMCO

The Cavity Shaft Wall System includes components that provide the strength to withstand lateral loads and fire protection necessary for walls that enclose elevator shafts, stairwells and other

USG Shaftwall Systems These systems are nonload-bearing gypsum panel partitions designed to construct elevator shafts, mechanical shafts, stairwells, air 

The USG Cavity Shaft Wall System includes components that provide the strength to withstand lateral loads and fire protection necessary for walls that 

For details of steel framed Partiwall system refer to USG Boral The clear distance between the SHAFTLINER fire barrier and wall framing on both sides 

Performance Selector All details, specifications, 14 USG Shaft Wall Systems USG-040912 Based on 4" C-H studs 25 gauge.

Technical Support 1-800-USG-4YOU Product Safety Hotline 1-800-507-8899 Product Categories

OVERVIEW CGC Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and

the Steel Stud Walls section. SHAFTWALL. USG Boral Shaftwall system utilises Rondo CH-Studs and other components as listed in Specialty Systems - Lift and.

CEMSCO products are manufactured to the standards established by the American Iron and Steel Institute. Veiw our resources on Typical Details-USG Shaftwall Assemblies here! Find a

Shaft wall limiting heights spans shaft wall limiting heights spans shaft wall limiting heights spans shaft wall ch stud

3 USG Shaft Wall Systems 09 20 00/USG BuyLine 2425 1 Hour Fire-rated Construction Non-loadbearing Acoustical Performance Construction Detail Description Test Number STC Test Number wt. 8 † 5/8 SHEETROCK® brand FIRECODE® Core gypsum UL Des U415, 31⁄ 8" panels, joints fi nished System A † 2-1/2 USG C-H studs 25 gauge 24 o.c. or U469

ALVANIZED. UL Evaluation Report. No. ER3660-02. Downtown Student Housing - San Jose State. San Jose, CA. I-Stud and USG Shaftliner. I-STUD Shaftwall System 

USG Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are finished later, along with interior partitions. Installation is quick and easy, using components and application procedures familiar to drywall contractors.